Sample-rate (span) presets were duplicated in three places and none was
authoritative: HPSDR set hardcoded in the desktop overlay (SPAN_RATES),
Pluto set in backend caps, and a separate hardcoded list in the web JS.
The web showed HPSDR rates even on Pluto, and the web adapter silently
dropped any rate outside a hardcoded HPSDR whitelist (so Pluto-only rates
like 960k/2304k never switched).
Single source of truth = backend caps -> controller:
- HPSDRNetwork.Caps now fills RatePresets [48k..1536k] (was nil).
- RadioBackend: named type TBackendRateArray.
- TRadioController.SampleRatePresets returns BackendCaps.RatePresets.
Both UIs derive from it:
- Desktop: ApplyBackendCapsToUI always feeds the overlay from
SampleRatePresets (overlay no longer owns the HPSDR list).
- Web: WebServer.SetRatePresets + rate_presets in state JSON; hosts
(daemon OnState/startup, GUI ApplyBackendCapsToUI/startup) push
SampleRatePresets; JS builds span buttons dynamically from it.
- WebAdapter.SyncSpan validates against SampleRatePresets instead of a
hardcoded whitelist, so any backend rate is accepted.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
- Status bar / web now show Pluto/LibreSDR model + serial instead of
"Unknown Board" (BoardDisplayName in controller; UI just renders it).
- Field 3 shows AD936x chip temperature + RX RSSI for Pluto (no PA →
Supply only for openHPSDR). Polled via backend.ReadTelemetry (~2 Hz),
filtered for sensor glitches (plausibility window + slew-limit, with
anti-stick) — fixes rare bogus -15°C readings.
- Add libiio binding iio_channel_attr_read_double.
- Remove stale root pluto_integration.MD (superseded by
doc/PLUTO_INTEGRATION_PLAN.md).
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
- RX hw-gain (Pluto/AD936x): backend SetRxGain(ModeIdx, GainDb) — gain_control_mode
(manual/fast_attack/slow_attack/hybrid) + hardwaregain. Controller FRxGainMode/
FRxGainDb, commands SetRxGainMode/SetRxGain/RxGainBy, rfRxGain event, snapshot,
applied in StartRunning. Persisted per-device (rx_gain_mode/rx_gain_db). HPSDR
unaffected (backend no-op).
- UI: separate "RF AGC" panel below the (unchanged) WDSP AGC block, shown only for
Pluto — FAST/SLOW/HYB/MAN mode buttons + manual GAIN slider. LayoutLeftPanel
reflows lower panels via RelayoutBelowBands; no layout shift on HPSDR.
- Cold-init fix: direct sampling_frequency write doesn't load the AD9361 FIR
decimation filter, so a cold-booted Pluto showed a wide centre spike that didn't
track tuning (worked only after SDR Console pre-initialised it). Add optional
libad9361 binding (dynamic) and call ad9361_set_bb_rate() in ApplySampleRate,
which configures BBPLL + loads the FIR; falls back to direct write if absent.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Add ADALM-Pluto / AD9361 support as a second hardware backend alongside
openHPSDR, sharing the WDSP DSP pipeline and the existing controller API
(UI stays decoupled from logic).
- RadioBackend.pas: abstract TRadioBackend + TBackendCaps + TRadioDevice
(Kind/URI/Serial). THPSDRNetwork now derives from it (state via virtual
getters); TRadioController.FNetwork is the base type.
- IIOBindings.pas: dynamic libiio loader (runs without libiio present).
- PlutoBackend.pas: scan/probe-by-URI, connect, LO/rate/bandwidth/gain
control, RX streaming thread (int16->24bit BE -> OnDDCIQ), Q conjugated
to match WDSP IQ convention. Verified on LibreSDR (AD9361) over network.
- Unified discovery: TDiscoverThread scans both backends; network Plutos
found via direct ProbeURI (no mDNS needed). ConnectDevice dispatches by
Dev.Kind (EnsureBackend swaps backend, preserving callbacks).
- DeviceStore/DeviceForm: persist Kind/URI/Serial; save Pluto via
AddSavedPluto so saved/autostart devices reconnect across restarts.
- VHF/UHF band plan (BoardUtils, kind-aware): 6m..ADS-B for Pluto; fixes
HF clamps (band detect, mouse-wheel 60 MHz cap, freq-display max).
- SampleRateOverlay: configurable presets (Pluto 576k..5760k, >520 ksps),
auto-width to fit.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
ew8bakandClaude Opus 4.8